how to install laminate flooring How To

How To Install Laminate Flooring

Installing Laminate Flooring

Laminate flooring has the exact same excellent look like hardwood floorings. The following detailed guidelines will show you how you can install a floating (without glue, nails or staples) laminate floor.

Tools & Materials to Install Laminate Flooring


Circular Saw
Table Saw (optional).


Laminate Flooring.
Underlayment (if required).
Dampness/ Vapor Barrier (if called for).


Interlacing laminate floating floors can be installed over clean as well as level ceramic, vinyl, concrete or plywood/ OSB subflooring. Normally, laminate flooring can not be installed in spaces with a floor drainpipe. See to it you follow all neighborhood building ordinance when mounting flooring.

Put on shatterproof safety glasses when cutting the laminate pieces.

Excellent to Know

For comfort and safety, use knee pads, a soft pad or a towel under your knees when mounting flooring.

Prep work

Step 1.

Read the supplier’s guidelines prior to the installment. In addition to installation steps, you’ll find information on different kinds of subfloors as well as dampness tests. The steps listed below define laminate flooring setup, yet always adhere to the directions for your certain flooring.

Step 2.

Prepare the subfloor.

Step 3.

If required by the supplier, install underlayment and also a dampness obstacle, seeing to it that the leading surface area side is set up as advised. Numerous laminate floors have the underlayment pre-attached to the bottom.

If you are installing laminate flooring over a concrete subfloor, a wetness obstacle is called for.

Step 4.

Location the flooring materials in the setup room for at the very least 72 hours before installing them so they could accustom to the temperature level and also humidity arrays advised by the producer.

Installing the Very First Rows.

Step 1.

Flooring Assembly Order

When mounting the flooring, assemble the pieces in the order displayed in the representation.

Step 2.

Loosely lay the very first row with the tongue of the boards facing the starting wall surface.

Step 3.

To prep the slabs in row one cut the tongue off the long side of every one of the items. Utilizing a table saw makes the tongue removal very easy. Simply establish the fencing at the proper size and also cut the boards.

Step 4.

Flooring Spacer

Location spacers between the laminate planks and nearby walls for the manufacturer’s suggested expansion space. Most makers call for an expansion void of 1/4 of an inch.

Step 5.

Start assembling the first couple of rows of laminate boards concerning 2 feet away from the starting wall. As soon as the first couple of rows have actually been set up, you could thoroughly glide the flooring into its last position.

Step 6.

Cutting Flooring

Cut the first piece of row 2, adhering to the maker’s instructions for startling the joints between rows.

Usually, at the very least a 12-inch stagger is recommended.

Startling the seams at each row strengthens the floor as well as enhances its look by providing it a more arbitrary pattern.

To cut the flooring, lay the board on its face (base up) and cut with a saw equipped with a fine-tooth blade for flooring.

Step 7.

Linking Slabs

Place the tongue of the lengthy side of row two right into the groove of the first slab of row one. You might have to utilize a mild angle to establish the tongue in the groove. Simply press the board down until it locks in place.

Step 8.

Affix the next item of row one

Once more, place the tongue at a small angle right into the groove and also push down to secure it.
Make sure the planks are aligned and also the surface area is even at the joints.

Step 9.

Add the next item of row 2.

Insert the tongue right into the long side of row one, slide the item towards completion joint, after that weigh down to secure the joint.

This locking technique needs to be made use of for the rest of the installation.

Step 10.

After you have actually installed the very first two planks of each row, position a weight, like a toolbox or a carton of flooring, in addition to the very first slabs to hold each row in area.

Step 11.

Continue mounting the very first 2 rows, securing a plank for row one, then a plank for row two. Utilize this pattern to finish the rows. Trim the last item to enable spacers as well as the growth space if required.

Step 12.

Utilizing a Tapping Block

A tapping block might be needed when a plank can not be turned, such as under a doorframe.

Setting the board as close as possible to its ended up place under the doorframe.

Follow the manufacturer’s directions for making use of the touching block. Typically, you position it along the groove side of the slab, after that utilize a dead impact hammer to touch the slab into location, locking the joint.

Step 13.

Once the first 2 rows are assembled, move them right into placement versus the starting wall surface. Make certain to keep the manufacturer’s recommended expansion gap with flooring spacers.

Mounting the Remainder Of The Floor

Step 1.

Proceed setting up the laminate flooring, startling the joints at the very least 12 inches as well as maintaining the development gap.

Excellent to Know.

Use cut items to begin rows, making certain the joints are startled properly.

Step 2.

Installing Around a Vent.
When laying the flooring around obstructions, like floor vents, cupboards or columns, cut the flooring to fit with a jigsaw.

To install the flooring around pipelines, you might require to make use of a jigsaw and also timber adhesive making the slabs fit correctly.

Cut a notch in the flooring to fit about the pipe.
With the smaller excess piece, sufficed to fit on the other side of the pipeline.
Set the smaller item in position and also connect it to the bigger slab with wood glue along the cut line( s).

Step 3.

Applying Silicone Sealer.
Examine the maker’s instructions for using silicone sealant in areas with high wetness levels, such as a restroom, utility room or kitchen. Excess dampness under the planks can damage the flooring.

When setting up around a tub or sink, apply silicone sealant to develop a watertight seal.

You’ll have to take some unique actions when setting up around a toilet. See Replace a Toilet for more guidelines on eliminating and installing a bathroom.

Eliminate the toilet.
Cut the flooring to fit about the drainpipe. Keep in mind to represent the maker’s needed development void.

Install the flooring.
Apply silicone sealer in the expansion space.
Allow sealer to dry, then re-install the commode.
Check the producer’s instructions for applying sealer along kitchen area cupboards that house a dishwasher or fridge.

Step 4.

For the last row, you might have to cut the pieces to fit.

Procedure the width required for the last row and deduct the producer’s development space.
Step to the board surfaces (leaving out the tongue) as well as split (cut lengthwise) the last boards along the groove edge.
Some flooring items have a little plastic tongue in the brief side groove of the slabs which assists lock the assemble. Make sure to remove the plastic tongue prior to cutting the length of the board.

Step 5.

Using a Pull Bar.
Use a pull bar and hammer to lock the last row in the area.

Finishing Up

Step 1.

Install change strips at entrances as well as where the floor satisfies other sorts of flooring, adhering to supplier’s directions.

Step 2.

Eliminate the wall spacers once the transitions remain in place.

Step 3.

If you installed a different underlayment, cut the extra.

Step 4.

When mounting in a restroom, cooking area, utility room or along an exterior door, use silicone sealer in the growth area around the border of the floor. This ought to be done once the entire floor remains in place.

Step 5.

Install the baseboards as well as footwear molding to the wall surfaces as needed. Connect the trim as well as shoe molding to the wall surfaces. Do not affix them to the flooring.

Step 6.

Maintain one or two cartons of your laminate flooring so you could repair any kind of potential troubles in the future, like a harmed board.